Stainless Works

Stainless Works Legend Sound Cat-Back Exhaust w/ H-Pipe, Performance Connect, Quad Tips – 2026 Mustang GT | M24QUADHPCL

$2,845.25
Shipping calculated at checkout.
  • Fitment guaranteed
  • Ships in 1–3 business days
  • Secure checkout

The Stainless Works Legend Sound Cat-Back Exhaust (part number M24QUADHPCL) is a 3-inch system for the 2026 Mustang GT, intended for builds that already run Stainless Works Performance Connect long tube headers. It uses an H-pipe crossover, Legend mufflers, and four polished exhaust tips. The goal is a deeper, more traditional muscle-car tone than the factory exhaust provides. Stainless Works says the system stays smooth at cruising speeds and gets noticeably more aggressive under heavier throttle.

This is not a standalone upgrade for an otherwise stock car. It bolts directly to the Performance Connect long tube headers and completes a header-back exhaust build. It is not designed for factory manifolds, factory mid-pipes, or Factory Connect header versions. For S650 owners who have committed to long tubes and want a finished system, the tubing is mandrel-bent and TIG-welded 304L stainless steel, and the system weighs less than the stock mufflers and piping.

Key Features

  • Legend mufflers tuned for a smooth low-end growl with consistent tone through the rev range
  • 3-inch 304L stainless steel tubing, described by the manufacturer as aircraft-grade
  • Mandrel-bent tubing with TIG-welded construction
  • H-pipe crossover that balances back pressure and rounds out the exhaust note
  • Quad polished tips that sit beneath the rear valence in a factory-like layout
  • Lighter than the stock mufflers and piping
  • Fixed-length configuration built only for Performance Connect setups
  • Bolts directly to Stainless Works Performance Connect long tube headers
  • Reuses the stock hangers; clamps and hardware are included
  • Manufacturer part number: M24QUADHPCL

Mandrel-Bent 304L Stainless Steel Construction

Stainless Works builds this system from 3-inch 304L stainless steel, which the manufacturer calls aircraft-grade. The tubing is mandrel-bent, so the pipe keeps its full diameter through each bend instead of pinching down the way crush-bent tubing can. Stainless Works says this approach supports both strength and exhaust flow.

All joints are TIG-welded. The four exhaust tips carry a polished finish, giving the rear of the car a clean, finished look.

Performance and Benefits

The sound comes from two parts working together. The H-pipe crossover balances the pressure between the two banks and produces a fuller, rounder note. The Legend mufflers keep overall volume in check while preserving that tone. Stainless Works describes the result as a throaty rumble that stays composed at cruise and turns aggressive when you open the throttle, loud where it matters without sounding raspy or excessive.

According to the manufacturer, the system is lighter than the factory mufflers and piping it replaces. No specific weight figure is given.

Installation

  • Bolts directly to Stainless Works Performance Connect long tube headers, which are required for installation
  • Will not fit factory exhaust manifolds or factory mid-pipes
  • Not interchangeable with Stainless Works Factory Connect headers
  • Fixed-length design with no length adjustment
  • Reuses the factory exhaust hangers; clamps and hardware are supplied
  • Tuning is highly recommended for full header-back exhaust setups
  • Stainless Works recommends professional installation to get proper alignment and clearance

Why You Need This

  • Completes a header-back exhaust build on a 2026 Mustang GT already running Stainless Works Performance Connect long tube headers
  • Replaces the quiet factory sound with a deeper, traditional muscle-car tone that stays manageable at cruise
  • Mandrel-bent, TIG-welded 304L stainless tubing provides durable construction in a full 3-inch diameter
  • The H-pipe and Legend muffler combination targets a rounded note rather than a raspy one
  • Weighs less than the factory mufflers and piping it replaces
  • Four polished tips under the rear valence keep the rear of the car looking close to factory

Vehicle Fitment

  • 2026 Ford Mustang GT

Fitment notes:

  • Not compatible with factory active exhaust systems
  • Will not fit factory manifolds or mid-pipes
  • not compatible with stock exhaust components

What's Included

  • H-pipe crossover
  • Legend mufflers
  • Quad polished exhaust tips
  • Clamps and hardware

Not included:

  • Stainless Works Performance Connect long tube headers (required for installation)
  • Exhaust hangers (the factory hangers are reused)
Shipping & returns

In-stock parts ship in 1–3 business days. See our refund policy for return details.

Fitment & install help

Not sure it fits? Contact us with your year, trim and options before ordering.