The American Racing Headers 160235 is a long tube header system for the seventh-generation Mustang with the 5.0L V8, built with 2-inch primary tubes and 3-inch collectors. This is the catless version of the ARH Long System, so it has no catalytic converters, and it ships with a 3-inch X-pipe as standard equipment. ARH offers the system in 1-3/4-inch, 1-7/8-inch, and 2-inch primary sizes. The 2-inch version covered here is the one the manufacturer intends for max-effort builds.
Manufacturer-stated gains: American Racing Headers states performance gains of up to 30 RWHP (rear-wheel horsepower) for its Long System on the seventh-generation Mustang. The manufacturer does not specify the test conditions, the supporting modifications, or whether this figure applies specifically to the 2-inch catless configuration.
The system replaces the restrictive factory exhaust manifolds and mid-pipe section on 2024-2026 Mustang 5.0L models. ARH states the Long System can add up to 30 rear-wheel horsepower. It connects to the car's existing axle-back after a mark-and-cut step, with no welding required. Each system is made in the USA from 304 stainless steel, with thick laser-cut flanges, TIG-welded inlets ported by hand, and merge collectors with scavenger spikes. It suits owners who want long tube header performance while keeping their current rear exhaust.
Key Features
- 2-inch primary tubes with 3-inch collectors, the size ARH designates for max-effort applications
- Catless (no catalytic converters) configuration
- 3-inch X-pipe included as standard
- Constructed entirely from 304 stainless steel
- Flanges are 3/8 inch thick and laser cut, which helps them resist warping and keep a consistent seal
- Inlets are ported by hand and joined with TIG welds
- Primary tube routing designed for fitment and performance
- Merge-style collectors fitted with scavenger spikes
- Connects to the existing axle-back with a mark-and-cut procedure, no welding needed
- Manufactured 100% in the USA, with no outsourced production
304 Stainless Steel, USA-Made Construction
American Racing Headers builds this system entirely from 304 stainless steel. Every unit is made in the USA, and ARH states it never outsources production.
The head flanges are 3/8 inch thick and laser cut. The extra thickness helps them stay flat through repeated heat cycles, so they continue to seal against the cylinder head. At the inlet of each primary, the tube is ported by hand and TIG welded, which gives a clean transition where exhaust leaves the port.
Performance and Benefits
The 2-inch primaries feed into 3-inch collectors, and this is the largest primary size ARH offers for the platform. The manufacturer positions it for max-effort builds. ARH routed the primary tubes with both chassis fitment and exhaust flow in mind. The merge collectors use scavenger spikes to help combine the pulses from each primary as they enter the collector.
The included 3-inch X-pipe carries the larger exhaust diameter back toward the rear of the car. Because this is the no-cat version, there are no catalytic converters in the system. ARH rates the Long System at up to 30 RWHP over the factory exhaust, which it describes as restrictive.
Installation
- Connects to the vehicle's existing axle-back exhaust
- Requires a mark-and-cut step to join the system to the axle-back
- No welding is required
Why You Need This
- Replaces the factory exhaust manifolds with long tube headers, for a manufacturer-stated gain of up to 30 RWHP
- The 2-inch primaries and 3-inch collectors are sized for max-effort 5.0L builds
- Keeps your existing axle-back, and joining the two takes no welding
- A 3-inch X-pipe is included, so no separate mid-pipe purchase is needed
- The 304 stainless steel construction and 3/8-inch laser-cut flanges are built to hold up to heat cycling
- Made entirely in the USA
Vehicle Fitment
- 2024-2026 Ford Mustang (5.0L)
What's Included
- 2-inch x 3-inch long tube header system
- 3-inch X-pipe
Not included:
- Catalytic converters (this is the no-cat version)