{"product_id":"american-racing-headers-1-3-4-x-3-long-tube-headers-direct-connection-system-no-cats-2024-2026-mustang-5-0l-160237","title":"American Racing Headers 1-3\/4\" x 3\" Long Tube Headers Direct Connection System - No Cats (2024-2026 Mustang 5.0L) - 160237","description":"\u003cp\u003eAmerican Racing Headers part number 160237 is a long tube header system for the seventh-generation Mustang with the 5.0L V8. This version pairs 1-3\/4 inch primary tubes with a 3 inch exhaust and is part of the manufacturer's Direct Connection System. It is the no-cats configuration, so it does not include catalytic converters. The system is built to replace the factory exhaust manifolds, which American Racing Headers describes as a restriction that holds back the Coyote engine's power and torque.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eManufacturer-stated gains:\u003c\/strong\u003e American Racing Headers states gains of up to 30 rear-wheel horsepower for its Direct Connect header kit. The source does not specify the test conditions, supporting modifications, or tuning used to reach that figure.\u003c\/p\u003e\n\u003cp\u003eThe Direct Connection design is meant to tie into the factory catback exhaust without any cutting or welding. The headers are made entirely of 304 stainless steel and manufactured in the USA. They use thick laser-cut flanges, hand-ported inlets, and merge collectors with scavenger spikes. For owners building a dedicated track or competition 2024 and later Mustang GT or similar 5.0L car, this kit adds long tube headers while keeping the stock catback in place. American Racing Headers states that the product is intended for racing use only.\u003c\/p\u003e\n\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e1-3\/4 inch primary tube diameter\u003c\/li\u003e\n\u003cli\u003e3 inch exhaust sizing\u003c\/li\u003e\n\u003cli\u003eNo-cats configuration, with no catalytic converters included in the system\u003c\/li\u003e\n\u003cli\u003eConstructed entirely from 304 stainless steel\u003c\/li\u003e\n\u003cli\u003eFlanges are 3\/8 inch thick and laser cut to resist distortion and keep the gasket surface sealing properly\u003c\/li\u003e\n\u003cli\u003eInlets are ported by hand and joined using TIG welding\u003c\/li\u003e\n\u003cli\u003ePrimary tube paths are engineered for both fitment and performance\u003c\/li\u003e\n\u003cli\u003eMerge-style collectors fitted with scavenger spikes\u003c\/li\u003e\n\u003cli\u003eDirect Connection System designed to mate with the factory catback without cutting or welding\u003c\/li\u003e\n\u003cli\u003e100% manufactured in the USA, with no outsourced production\u003c\/li\u003e\n\u003cli\u003eManufacturer part number 160237\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eUSA-Made 304 Stainless Steel Construction\u003c\/h3\u003e\u003cp\u003eAmerican Racing Headers builds every part of this system from 304 stainless steel. The company states that its production stays entirely in the USA and is never outsourced.\u003c\/p\u003e\u003cp\u003eThe head flanges are laser cut from 3\/8 inch thick material. Thick flat flanges like these are designed to stay true through repeated heat cycles, which helps maintain a reliable seal at the cylinder head. Each inlet is ported by hand to smooth the transition from the exhaust port into the primary tube, and the joints are completed with TIG welds.\u003c\/p\u003e\n\u003ch3\u003ePerformance and Benefits\u003c\/h3\u003e\u003cp\u003eThe 1-3\/4 inch primaries are routed to balance fitment in the engine bay with exhaust flow, then feed merge collectors equipped with scavenger spikes. A merge collector with a scavenger spike is designed to smooth the point where exhaust pulses from the individual primaries combine, helping move gases out of the cylinders efficiently.\u003c\/p\u003e\u003cp\u003eBecause this is the no-cats version, there are no catalytic converters in the exhaust path between the collectors and the catback. The manufacturer offers a 1-7\/8 inch primary option for max-effort builds, which makes this 1-3\/4 inch system the smaller of the two primary sizes in the lineup.\u003c\/p\u003e\n\u003ch3\u003eInstallation\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eDesigned to connect to the factory catback exhaust\u003c\/li\u003e\n\u003cli\u003eNo cutting or welding is required to integrate the system with the stock catback\u003c\/li\u003e\n\u003cli\u003eAmerican Racing Headers states this product is manufactured exclusively for racing; installing it removes the vehicle's legal use on public roads and highways and may lead to fines or criminal liability under the Clean Air Act\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy You Need This\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eReplaces the factory exhaust manifolds on a 2024-2026 Mustang 5.0L with long tube headers, for which the manufacturer claims up to 30 RWHP\u003c\/li\u003e\n\u003cli\u003eWorks with the stock catback, so you can add headers without cutting or welding the existing exhaust\u003c\/li\u003e\n\u003cli\u003e304 stainless steel construction and 3\/8 inch laser-cut flanges are built for durability and a lasting head seal\u003c\/li\u003e\n\u003cli\u003eHand-ported, TIG welded inlets and merge collectors with scavenger spikes reflect detailed header fabrication\u003c\/li\u003e\n\u003cli\u003eMade in the USA by American Racing Headers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eVehicle Fitment\u003c\/h3\u003e\u003cul\u003e\u003cli\u003e2024-2026 Ford Mustang (5.0L)\u003c\/li\u003e\u003c\/ul\u003e","brand":"American Racing Headers","offers":[{"title":"Default Title","offer_id":68305310056633,"sku":"ARH-160237","price":1913.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0835\/3182\/5337\/files\/Mustang_Direct_Connection_6b4af842-679f-4fe6-bfcb-d25c0ecd5b72.png?v=1794430345","url":"https:\/\/engmustangs.com\/products\/american-racing-headers-1-3-4-x-3-long-tube-headers-direct-connection-system-no-cats-2024-2026-mustang-5-0l-160237","provider":"ENG Mustangs","version":"1.0","type":"link"}